Jim Wink's Make Blog

A while back I ordered an Attiny 2313 from Adafruit . Along with it I ordered a USBtinyISP to program it. For whatever reason I could never get the thing working.  The process involved downloading AVRDude , WinAVR , and various steps of setup. After getting everything installed & following the instructions carefully, I still couldn't get it to work. I did submit some questions on Adafruit's forum & got some answers, but I suspect the problem was either I'd made a mistake in assembling the   USBtinyISP  or just my general lack of understanding of what was going on. It was also possible I'd wrecked the chip, so I gave up after a while. Later I decided it might have been better to take myself out of the equation, so again I ordered another programmer and some chips, this time from Sparkfun: a Pocket AVR programmer , another Attiny 2313 and an Attiny85 . So far I've not gotten around to trying out their AVR programmer & until recently the chips staye...

Because it was quick and because I wasn't getting much done on other projects, I decided to look into Persistence of Vision (PoV) . PoV was fairly simple to set up with the RBBB . I put the RBBB in a breadboard, ran a patch to the ground rail and added in five blue LEDs. I started with a sketch of my own that sort of worked, but not well. So I figured I'd have more luck looking on the Arduino playground . There I clicked on Interfacing with Hardware and searched on PoV. There I found a link to an art icle written in German by someone named Michael Zoellner. I didn't understand the German but the sketch that was linked had comments in English. I made some tweaks to the code to allow for adjustments and ran it. It worked fairly well so I updated the setup so I didn't have to run it off of the USB cable & added battery power. This made it easier to hold it in my hand and wave it in front of a camera. I set up a camera on a tripod, lowered the ISO to 100 and turned d...

I haven't posted in a while. I have still been busy tinkering, but for one reason or another haven't gotten around to posting. I have made some progress on my design for a color fading juggling ball, and have started some other projects, but I think I will save them for another post. Instead, I'll say a word or two about some new purchases. When I built the web cam pan this summer, I sent with it my one and only Arduino. It was an older one with an Atmega 168 and 16 k of memory so I was looking to upgrade. Prior to sending it off, I first bought an Arduino Pro Mini 5.5v / 328 from Sparkfun . I also had to get an FTDI breakout board for it as it doesn't have on-board USB communications. Man, that thing is tiny! It's about the size two postage stamps! Pictured here is what it looks like after putting pins all over it so I can snap it into a breadboard. I did learn one thing with it - solder carefully. The picture you see here is actually my second Pro Mini. With...

Here is a photo of a project I started a while back. I took an old Logitech web camera we had sitting around, removed it from it's case and sandwiched it between two small sheets of Acryllic. My reasoning here is it would be easier to attach that to a servo than the weird sphere casing it was originally in. Really, I think it just looks cooler that way. The servo is bolted to - well through - a plank I had in the garage. I think it's left over from building the deck. A plank, yes. Probably green-treat or some such. If I could've figured out a way to get duct tap on it, I probably would have. Anyway, behind the web camera is an Arduino Duemilanova (168) - the original/first one I got. It's connected with some simple wood screws through the board. Underneath all this, on the other side of the plank is a Power Switch Tail . This nifty little device is a bit like a really short extension cord with a switch. Regular 120 volt house current goes in one end and comes out the ot...

Axman Surplus is awesome. I've been thinking of building a CNC . There are a number of articles on the web that'll walk you through building a CNC, including this one on how to build a desktop CNC . That one, in particular, could use a tool I already have - a Dremel. Anyway, a CNC is complicated. There's a whole language used for communicating with CNC's called g-code , that is pretty much a complete mystery to me. Then there's taking 3-d models and converting them to g-code, and probably any number of details I don't have figured out. It'd be a bigger project than I've tackled so far. But like anything, I've got to start somewhere, so I figured I'd start with equipment I already have. In this case I'm referring to the Motor Shield I got from Adafruit . I built it a while back and then set it aside and never used it. So I figured this was a good time. I'd already figured out how to run a servo on the Arduino, but the Motor Shield has p...

It should come as no surprise that I am still somewhat obsessed with my accelerometer. I've stated earlier that I'd like to create a lighted juggling ball that changes color as it rotates. This should be a simple task with an accelerometer - three axis, three colors, mix 'em and you're done, right? Maybe not so much. I won't rehash previous posts, but I will say I am really close. I should, however, explain my criteria: Rotation should change color of the light, obviously At a minimum, there should be shifting between the 3 basic colors: red, green, blue I'd prefer 6 colors total, with the other 3 being mixes: yellow (red/green), aqua (green/blue), and purple (blue/red) I'd like to get some nice fading as it switches between colors, but as I'll point out later, this is somewhat hard The light intensity should never change - all on, and never off I'd prefer it if there wasn't much white - all colors on - showing I already have code on the Arduin...

So far in this blog I have not posted at all about what I do for a living. I've only posted about one of my many hobbies. But today I ran into something I wanted to share. I could go on and on about how I could share it (Facebook, Yammer, emails to hapless co-workers, emails to hapless friends, drone on and on to my wife about it) but I won't. Much. Instead, I'll post it here. Here where it can quietly sit where few, if any, will see it. But I can always go back and get a chuckle about it. Anyway, what I do for a living is write software. I am a software engineer. I've created software in a number of different languages: Pascal, COBOL, C++, Visual Basic, Java, C# - probably others I am forgetting - and I've been doing it for over 17 years now. Strange, but true. This blog is about stuff I make. Software is stuff I make, right? Okay, boring stuff I make - I'll try and keep it to a minimum. Anyway, I'm currently contracting at a company that uses Oracle (10g?)...